| Detailed Product Description： | First, the product uses
GQ40 steel cutting machine, it is trial and construction works on a variety of reinforced concrete, carbon steel and hot rolled round steel and rebar. Can also cut off the flat iron, square steel and angle steel.
Second, product characteristics
1, small size, good quality, compact, compact and reliable.
2, the lubricating performance: a box-type closed structure, gear to splash lubrication, in turn fueling the continuous operation can be used on more than one month.
, Functional loss less: rolling bearing lubrication conditions improve, the gear shaft end, compared to the same load power can be reduced by one third compared with the same type of cutting machine cutting machine on the same type.
4, easy to move: front-wheel steering, flexible, and easy maintenance.
5, the machine configuration of high-quality zero components, heavier chassis, heavy-duty pulley <70 kg>, thicker side cover, the use of lipid lowering crankshaft, lipid crank wheel configuration segment fight knife block, heavier rod, copper crankshaft W GB the 3KW line motor seal guard, just the clutch sleeve, increase the caster, thickening of the lid with a toolbox, 20A the Delixi electrical with thermal relay, high-quality belt, high-quality bearings, thick blade, plus thick pressure of the knife, high-quality cutter, plated dual-use light clutch lever.
Second, the main technical parameters
Cut off the bar diameter: 6/40 (steel tensile extent the UB in ≦ 450mpa below)
Cut off the flat maximum size: 70 × 15
Cut square steel specification: 32 × 32
Cut off the angle of maximum size: 50 × 50
Cutter nominal stroke: 34
Continuous cut the number of 32 beats / min
Motor power: 2.2/3KW voltage, 380V Speed: 2880r/min
Dimensions: 1250 × 500 × 730mm
Machine weight: 485KG
The bar diameter 20mm up and down at the same time cut off the root of the number of recommended table
Bar diameter (mm) 6-8 9-13 4-18 19-20 20
Each cut off the root of the number 65321
Note: When you disconnect the low-alloy reinforced bar maximum diameter of not more than 36mm
Third, the machine the main structure
This machine consists of a running wheel group, rotational structure, the composition of the body, clutch, heads, knife block.
Transmission, the motor with the drive to make the big pulley rotation coincide in the same shaft coupling gear and gear, swimming in the large gear shaft coupling gear and crankshaft agreement passed to the twisting force of the crankshaft-driven shear rod to promote the scissors knife block shear.
Fourth, the use and safety precautions
(A) preparations before use
A hand rotation, check the gear consistent with normal, whether stuck phenomenon.
2, check the blade is installed correctly firm, the gap between the two blade horizontal gap should be 0.2mm-0.5mm range in 0.2mm-0.5mm within.
3, check all parts of bolts detained (large side cover bolts should be regular checks to prevent loosening).
4, check the electrical equipment is normal, to ensure good insulation, pay attention to the use of three-phase four-wire, to ensure proper grounding, grounding after commissioning to drive the direction of rotation direction of the arrow should be shown in the belt cover consistent
5, the new machine prior to use to open the oil filler cap (through the filling hole in the machine top cover panel to window Excellencies two-thirds diameter) to the machine cavity and N150-220 # gear oil.
6, no-load test 10min, if the abnormality is found should be promptly downtime.
(B), the process of using Notes
1, must be reinforced to cut off tool the middle of the upper part of the tool may not be used unless absolutely necessary, in order to avoid the body tail fatigue
2, the fixed blade shape is rectangular (84 × 70mm) cut reinforced the following 32mm/38mm, with the long side cutting edge, cut reinforced 32mm/38mm above, the short side cutting edge, attention to check the blade during use if loose, the blade edge chipping tool change or replacement of the blade, in order to avoid the blade blunt the cutting resistance increases, damage to other parts.
(C) use of pedal clutch
1, will be to cut the steel on the cut off position, the eccentric the block iron (Balenghaitang, iron) to the appropriate edge snapping reinforced foot under the clutch pedal can be cut off, riding a cut off time, the pedal shall not exceed 2 seconds, or consecutive to a knife.
2, the machine to remove the jaws of death within the pad to replace the dedicated blade cutting angle can be cut angle (cut angle blades need to order supply)
3, the clutch pedal should clutch tread in place, often imaginary tread in place will cause the clutch to premature failure.
Five, maintenance and lubrication
1, clean the various parts of the dust and debris.
Often view the body oil level is above the groove in the oil standard.
3, when the machine such as a long time to stop working, you need the motor removed.
Fuel use for the first time a month should be replaced with new oil, once a calcium-based grease (butter) should be added to the bearing 6. |
| No.8764083
